Open LPBF Buildstylefor Autodesk Fusion
Build part parameters · group grp_border_first

First border (beam compensation)

The first border is the outermost laser path of every island. It runs a little inside the part outline, by the beam compensation, so that the melted edge ends exactly on the outline. Walls too thin for that offset get a blocked path along their middle instead.

In Advanced Toolpath Utility

    Try it yourself

    Open the parameter profile of your part (Open Profile in the Exposure Preview), expand First border (beam compensation) and type a beam compensation. Rebuild and zoom into a corner of the Exposure Preview: the red outline of the part stays, the border moves inwards. Thin features show the blocked path along their middle.

    The video uses 0.2 mm, much more than a real beam compensation, so the shift is visible at all. The demo part parts/border_block.stl (a block with a chamfer, a round corner and a 0.1 mm fin) is generated by tools/make_parts.py.

    Try it

    0.060 mm 0.120 mm
    first border (BSID 100) blocked path (BSID 110) hatch powder

    Why compensate?

    The laser does not melt a line but a track of roughly 0.1 mm width. If the beam centre ran exactly on the outline, half of the track would lie outside and the part would grow all around. The first border therefore runs half a track width inside: the beam compensation, 0.06 mm by default. In the Edge view, set b and the track width w; the melted edge is on the outline when b = w/2.

    All other rings are measured from the same outline: following borders and fill contours further inside, and the hatch starts hatch offset (0.05 mm) inside the innermost ring.

    Thin walls and blocked paths

    The border is the outline shifted inwards by b. A wall narrower than 2 · b disappears in that shift, so neither border nor hatch would melt it. The blocked path fixes this: one open line along the middle of such a region. Open the Thin fin view and make the fin wider than 2 · b: the border then runs around the fin and the blocked path disappears. Untick Blocked paths to see what stays unexposed.

    In the demo the 0.1 mm fin gets a blocked path with b = 0.06 mm. With b = 0.2 mm it starts 0.19 mm inside the block instead of 0.03 mm, and its end moves back from the tip by 0.22 mm instead of 0.05 mm.

    Blocked paths shorter than the minimum blocked path length (0.02 mm by default) are deleted. Raise the slider above the length of the fin's blocked path (about 1.2 mm) and it is removed, and the fin stays unexposed again.

    Direction and start point

    The melt pool and the spatter are not symmetric to the scan direction. Alternate direction every layer reverses the border on every second layer so such effects do not add up on one side. The closed path also starts and ends somewhere, which leaves a tiny seam; the default random start point spreads these seams. Step through the layers in the Direction view.

    The edge and fin views are drawn to scale in millimetres, but the melt track is a simplified half ellipse and the end trim of the blocked path is approximate. The direction view uses the outline of the demo block; the start points are random as in the buildstyle, not the ones ATU picks.

    Parameters

    ParameterDefaultMeaning
    First border (beam compensation)onSwitches the first border on.
    Beam compensation0.06 mm (0–2)Distance of the beam centre line from the outline.
    Blocked pathsonCentre lines in regions narrower than 2 × beam compensation.
    Minimum blocked path length0.02 mmShorter blocked paths are deleted.
    Alternate direction every layeronReverse the border on every second layer.
    Layer skip, Line stipple, Start point shiftsub-groupsExpose every n-th layer, dashes in several passes, start point mode (random by default).

    Laser settings (group Scanning)

    Vector typeBSIDPowerSpeed
    First border100150 W600 mm/s
    First border (downskin)101100 W900 mm/s
    Blocked path110150 W600 mm/s

    Borders are exposed after the hatches (scan order 80 and 85 against 40 for the volume), so they re-melt the ends of the hatch lines.

    In the code

    Follow the parameters from the dialog to the laser in How the code works, and change the defaults yourself with the recipes below.

    How the code works

    Seven steps from the profile dialog to the laser. Scroll through them: the drawing on the left shows what each piece of code does. Highlighted lines are the ones the text talks about; the file names link to the source.

    first border blocked path hatch

      Change it yourself

      How to try a code change
      1. Work on a copy or a git branch of the buildstyle project.
      2. Open the project folder in an editor such as VS Code. ATU writes jsconfig.json and type declarations into the folder, so the editor can offer code completion.
      3. Make the edit, save, compile the project in ATU and rebuild the exposures.
      4. Check the result in the Exposure Preview or the 3D View, like in the video above.